How to choose the right Douglasville Electrician

When it comes to picking the right electrician either for esidential or commercial projects; you must know where to begin your search. Most individuals might default to using the Internet to find relevant electrical companies. This is a good place to start but due to the volume of results from the search; it might still leave you confused. I would like you to think back to the times before the advent of the Internet, how were technicians chosen? The two top ways were by the works they do or by referral (word of mouth). The times have changed but the basics remain the same. Here are 3 tips that can help you choose the right Douglasville electrician:

A picture of Quincy who is an electrician in the Douglasville, Georgia areaUnderstand your Budget: You would not want to call an Electrician who charges an exorbitant rate if you have a better offer. However, it is not wise to use someone who charges a low rate but cannot deliver on the job. It is important to strike a balance that would give you quality at an affordable rate. It may be complex to know which Electrician would best serve your interests but with a little search; it should not be hard to find. Make sure that you have a reasonable amount so that you do not end up with a run-of-the-mill technician. In order to give speed to your search, it is important to ask your friends and acquaintance for recommendations.

Quality Service: It is ideal to look for an Electrician who has a reasonable track record of delivering on projects assigned to him. This is one of the criteria I believe is a safe route to get an Electrical expert. When you stay true to this age-long system of getting an expert, you would never go wrong. This is the method I used that made me discover The Electrician Squad. I went to an office and was impressed with the electrical works, wiring and the neat finishing. On further enquiry, I was given a website address to find out more about the Electrical contractor that worked for them. I did contact the Electrician Squad and I have continually been impressed with all the projects they have done for me.


Experience: It is important to settle for an Electrician that has years of experience under his belt. This would give you the assurance of knowing that anything they do would give you the required satisfaction. It is not essential to get overworked when you are searching for experience. As long as the person has a decent number of years under their belt, they are good to go. Most of the Electricians who have put in many years on the job have the pedigree to handle your projects without sweat. Interestingly, some of these technicians who fall under this range are quite affordable.


Generally, there are many factors that can be considered when you want to get a good Electrician. The items that were listed would help to set you in the right direction. In every choice you make, it is vital to ensure that you do not breach safety or environmental standards. It pays to go with an Electrician that has mastery of his field.


The Importance of The Home Inspection

Home Inspection Diagram

There are many things that go into a Property deal. The more every stakeholder understands the essentials, the better outcome that each party enjoys. One of the critical factors that affect the value of a project is the degree of Home inspection that goes into it: source ( A couple of individuals may argue about the direction of this piece but it is important to look at this from two angles. In order to keep things balanced, we would look at the angle of the Buyer and the Seller in a Home deal. We would evaluate the place of Home Inspection and how it gives vent to each transaction that is done.

In the light of the peculiarity that governs the property market, the seller can assess the true value of his home with the aid of experts. The certified evaluation gives leverage to the Seller to strike a good deal with his home. It is important to mention that the holistic review of the basic components such as the Structure, Electrical, Home systems and much more play crucial roles. No one is left in the dark on what to expect when the sale is consummated. This gives the right impression and puts a touch of integrity on the Seller.

Furthermore, the Seller has the opportunity of deciding if he would like to make an investment to upgrade his home. This is due to the report that is detailed and permits a restructuring to suit the Seller’s ideals. You can decide to rework the Electrical, add new structural designs to increase the value of your home. It gives the right base to project what you want to any interested buyer. Most of the homes that have undergone inspection stand a better chance to do well in the market.

Conversely, the benefits are not all tied to the Seller. They buyer has so many things that they can enjoy when Home Inspection is done. One of this relates to the composite understanding of what he is getting into. There are no grey areas and he can be guided to make an investment based on what he feels is a fair compensation for the house. Also, the Buyer can know the key areas to inspect before making a deal. This saves time and helps everyone to move with speed through the purchase process. In order to cut costs, the buyer and the Seller can use an Independent Company to do the Home Inspection.

On a general note, the buyer has a professional document that brings some measure of comfort. The use of various experts such as Surveyors, Structural Engineers, etc makes this a wise move. It takes away all the leg work that can make the process of buying a house complicated. Many buyers have come to understand that it is safer to use this channel and get a good bargain than go it alone and get burnt. In view of the projections that cover the aspects of buying and selling a property; it is ideal to keep it professional by engaging a Home inspection Company.


Replacing a Three-Way Switch

Don’t be zapped while fixing a three-way switch or replacing an old one with another. Although the work can be quite daunting, take caution as you stride down the boulevard of Electric Avenue and follow the advice of highly rated electrical contractors in Sacramento, CA. A three-way switch is a handy electrical convenience that facilitates light control from two different locations, such as the end and beginning of a staircase. If your switch does not have the words On or Off imprinted and it is one of two switches that can operate one light or a receptacle, then it is a three-way switch. The convenience switch derives its name from the fact it possesses three terminal screws.

To change a three-way switch, follow these easy steps:

  1. Put off the power that flows through the switch at the fuse or circuit panel.

The circuit board serves as the first point through which electricity goes through as it passes from the service entrance to the various areas in your house. The panel has the markings “On” and “Off” that control the power in the entire house. When doing electrical work in or around the house, it is always advisable to disconnect power by switch the fuse panel from on to off.

  1. Unscrew the switch plate and remove it; then test whether you still have power on the switch using a voltage tester.

Dealing with electricity requires caution owing to the danger such work poses. If there is power in the live wall fixture, it might cause serious bodily injuries. Testing if a fixture is live can be done with some mundanely found electrical appliances and should be done before commencing any work on any fixture. If you are in any doubt, consult an expert electrician. After unscrewing the switch from its box, pull it out while the wires are still on it.

  1. Take out the wires and Attach them to the new switch 

Once you remove the wires from the three-way switch, connect the tagged ones to the corresponding terminals of the new switch. You may also choose to switch one wire at a time to ensure that you do not do the attachments wrongly. If you track where each wire goes, the electrical work of replacing an old three-way switch is any harder than fixing a new single-pole switch. However, if the wires do not have tags, it can be quite difficult to figure out the proper connections.

  1. Put the newly wired three-way switch back and wind up the electrical repairs job

If the current switch has a green ground wire, put the wire to the green screw terminal on the replacement switch. Place the newly wired three-way switch back to the electrical box and tighten it correctly. Finish the electrical repairs by screwing the three-way switch and turn the electricity on.

Once you have changed the old switch with a new one and the trim plate is in place, test the switch. If you identified and connected all the wires correctly, then the switch and light should work just well. Congratulations on an electrical job well done. If the switch does not work properly, you might have to call a qualified electrician to do the troubleshooting and electrical repair.

Renew the Hardwood Floor of Your House

home-improvementPeople like to come home and feel welcomed. Much of this feeling is given by the interior of the house, and it’s very important to know how to decorate your house to get it. You don’t have to spend too much to achieve this, but you have to have a good taste in decorations.

It’s a custom to hire an interior decorator to do this for you, but if you use a little of your personality and some imagination, everything could turn out fabulous. What nobody tells you though is that you can do it by yourself and you can start with the floors.

Today we are talking about the hardwood floor and how important this is in a home.

The Age

Home-Improvement-Kitchen-DecorHardwood floor, as the name says, it’s made out of wood, cut and fit perfectly to offer it resistance and endurance. However, if your hardwood floor was installed some long time ago, you might observe that it has lost its shine or it has stains on it. This wouldn’t be a huge problem, but there may also be missing pieces or the hardwood might be stained in a strange color.

However, the age of the hardwood floor doesn’t matter too much, because you can easily restore its beautiful aspect, making it look brand new again.


The Aspect

There are different kinds of hardwood that might have been used for creating the floor, and if the wood is stained, you need to see what the original aspect was. Some wood has a beautiful look, without being stained with special substances or darker lacquer, so you’ll have to see how it looked at first.

Clear the Room

To start such a project, first of all you need to clear the room. If you can’t take out all the furniture from the house, especially if you have more rooms with home-improvement-lady2hardwood floor, simply do one room at a time. You will need an electrical sander and a source of electricity. Those are all the materials you will need in the beginning, and if you want to give the wood another color, you will need some cloth, stain and wood lacquer.


The electrical sander will help you bring the hardwood floor to its original aspect, eliminating all the stains and the wood lacquer, if there is any. However, if the wood has spots of oil or any other deep stain, this won’t come out with the sander.

Even so, this machine will help you also level the floor, making sure that there are no bumps in it. You don’t have to buy this, but you can borrow it from someone or simply rent it from the home improvement stores.

Cleaning the Dust and Debris

homeimprovementNow that you have sanded the whole room, you can see the original aspect of the wood. However, before you can go to the next phase, you’ll have to take out all the dust and debris that was left there after sanding.

This will prevent any imperfection to show if you choose to stain the wood or to lacquer it directly.


You can find this in the home improvement stores and it’s actually quite cheap. To know what you are looking for – it is a dark colored dust that is sold by pound or kilos. You will have to mix it with water and try it on a piece of wood. For two liters of water, you can add about two table spoons for a nice color. However, try it before you use it and add more stain if you want to get a darker color.

Now, all you have to do is take the cloth, soften it in stain and start rubbing the floor. You will see from the first time you apply it that the wood will simply absorb the color and the aspect will be wonderful.

429223You will have to cover the whole room with this, but make sure you apply it even.


Once this is finished, you will have to let the stain dry for a few hours, until the wood is good to be lacquered. Apply the wood lacquer with a brush, and make sure you apply it in even coats. When the lacquer will be dried, the hardwood floor will look brand new again, with a beautiful aspect.

This is actually a quite easy project, and if you want to learn more about how to renew your hardwood floor, you can read more here.